| AS-I DATA DECOUPL 2 X 4A SCREW AS-INTERFACE DUAL DATA DECOUPLING UNIT, IP20, SLIMLINE S22.5 SCREW-TYPE TERMINALS, MODULE WIDTH 22.5 MM, IN: 24 V / 30 V DC OUT: 2 X AS-I, 4 A INTEGR. OVERLOAD PROTECTION, INTEGR. EARTH FAULT DETECTION, SIGNALING CONTACTS, REMOTE RESET |
|
General technical data: |
Product brand name | | AS-Interface |
product designation | | Twin data decoupling module |
Design of the product | | SlimLine S22.5 - Module to beused in the IP20 control cabinet |
Protection class IP | | IP20 |
Installation altitude / at a height over sea level / maximum | m | 2,000 |
Ambient temperature | | |
| °C | -40… +85 |
| °C | -25… +70 |
Relative humidity / at 25 °C / during operating / maximum | % | 70 |
Item designation / according to DIN 40719 extendable after IEC 204-2 / according to IEC 750 | | A |
Item designation / according to DIN EN 61346-2 | | A |
Active power supplied | W | 240 |
Mechanical operating cycles as operating time / of the signal contacts / typical | | 1,000,000 |
Product function | | |
| | No |
| | Yes |
| | Yes |
- short-circuit to earth recognition
| | Yes |
- test function of signaling contacts
| | Yes |
- adapted for grounded AS-i networks
| | Yes |
- adapted for non-grounded AS-i networks
| | Yes |
- adapted for AS-i Power24V
| | Yes |
- sequential connected time-delay
| | Yes |
- AS-interface data decoupling
| | Yes |
Reset function | | yes |
Adjustable response current | | |
- of the current-dependent overload release
| A | 2.5… 4 |
Number of electrical connections / for alarm contact | | 3 |
Number of outputs / for AS Interface / maximum | | 2 |
Type of display / as status display by LED | | yes |
Number of switching contacts / as make contact / for reporting function | | 2 |
Design of the switching contact / as make contact / for reporting function | | yes |
Response delay time / of the sequential switch-in delay | ms | 200 |
|
Communication: | | |
Protocol / will be supported / AS interface protocol | | Yes |
|
Auxiliary circuit: | | |
Operating current / of the auxiliary contacts | | |
| A | 3 |
| A | 1 |
|
Ein- und Ausg?nge: | | |
Type of voltage | | |
| | DC |
Characteristic feature of the output / short-circuit protected | | Yes |
Output voltage | | |
| V | 30 |
| | |
| V | 20.5… 31.6 |
| V | 24 |
Output current / for DC / maximum | A | 8 |
Input voltage | | |
| V | 30 |
| | |
| V | 21… 32 |
| V | 24 |
Input current / for DC / maximum | A | 8.2 |
|
Short-circuit: | | |
Design of the short-circuit protection | | electronic |
|
Einbau/Befestigung/Abmessungen: | | |
Built in orientation | | vertical |
Type of mounting | | 35-mm DIN rail mounting or wall mounting with plug-in flaps |
Width | mm | 22.5 |
Height | mm | 101.3 |
Depth | mm | 121.2 |
Design of the electrical connection / for auxiliary and control current circuit | | screw-type terminals |
Product function / removable terminal for auxiliary and control circuit | | Yes |
Type of the connectable conductor cross-section | | |
| | |
| | 1x (0.5 ... 4 mm?), 2x (0.5 ... 2.5 mm?) |
| | |
- with conductor end processing
| | 1x (0.5 ... 2.5 mm?), 2x (0.5 ... 1.5 mm?) |
- for AWG conductors / for auxiliary contacts
| | 2x (20 ... 14) |
Verification of suitability | | CE / UL / CSA |
Acceptability for application / safety-related circuits | | Yes |
|
Certificates/approvals: | | |
General Product Approval | other | | |
| |
|
last change: | Dec 14, 2011 |